0061 RF Occupancy Or Vacancy Sensor User Manual Lutron Electronics

From Voting Rights Wiki
Jump to navigation Jump to search


Discuss with that product’s installation sheet for directions. Twist and remove mounting bracket to insert battery. Product Description Lutron’s ceiling-mounted Occupancy Sensors are wireless, battery-powered, passive infrared (PIR) gadgets that automatically control lights by way of RF communication with a dimming or switching device. These Sensors detect the heat from people moving within an space to determine when the area is occupied. The Sensors then transmit the suitable commands to the associated dimming or switching machine to turn the lights on or off routinely, offering both comfort and distinctive energy savings. Sensor does not carry out satisfactorily from this location, it could also be moved to 1.4 Ifanother location by pulling the Sensor straight down and repeating steps 1.Three and 1.4. 1.5 If the Sensor’s performance is satisfactory, it ought to be permanently attached to the ceiling tile, as described in section G. Everlasting Mounting. Temporary Stable Ceiling Mounting Use this procedure if the Sensor will be mounted on a stable, steady ceiling floor corresponding to drywall, plaster, concrete, or wood. Two 3M™ Command™ adhesive strips are supplied for quickly mounting and testing the Sensor on clean, strong ceiling surfaces. These strips are designed for easy, damagefree removing and are usually not reusable. These strips shouldn't be used for completely mounting the Sensor (see part G. Permanent Mounting ). Carefully comply with the removing directions beneath to ensure the ceiling is just not damaged throughout removing. Observe: Don't use the adhesive strips on ceiling tiles, as they'll doubtless cause injury to the tile upon removal. Easy-to-follow Directions Set-Up In order for the Sensor to operate properly, it should first be set up with a corresponding dimming or switching machine. The procedure for establishing a Sensor with a Maestro Wireless® (MRF2- only) Dimmer or Digital Swap is detailed below. P/N 041-172a 2.1 Peel the red "Command Strips" liner off of one of the adhesive strips and apply the strip to the flat facet of the mounting bracket as proven in the diagram. Note: Do not cowl the bracket’s screw holes as a result of they will be used to mark screw gap locations on the ceiling. Establishing a Sensor with a Maestro Wireless Dimmer or Digital Swap Dimmer Key Features · Low Upkeep. 10-year battery life. Convenient low-battery indicator. · Multiple Gadgets. Up to 3 Sensors can work collectively to regulate lights for broader protection in large areas. Each Sensor could also be added to up to 10 receiving gadgets. Sensor Operation Occupancy Version - The Sensor will mechanically turn the lights on when the area is occupied and automatically flip the lights off after the space is vacated. The Sensor will robotically turn the lights off after the space is vacated. There is a constructed-in 15-second vacancy grace period that begins when the lights are routinely turned off, during which the lights will automatically turn again on in response to motion. This grace period is supplied as a safety and comfort characteristic in the occasion that the lights flip off whereas the room is still occupied, in order that the user does not need to manually flip the lights again on. After 15 seconds, the grace interval expires and the lights should be manually turned on. This Sensor is part of a system and cannot be used to control a load with out a appropriate dimming or switching device. Discuss with the instruction sheets of the receiving device(s) for set up info. The Sensor could also be installed up to 60 ft (18.Three m) away from the associated dimming or switching system(s) if they are in direct line of sight. If there are walls or different boundaries between the Sensor and receiving machine(s), the Sensor needs to be located inside 30 ft (9.1 m). Caution: This product should not be used to control tools which might create hazardous situations, such as entrapment, if operated by chance. Sensor in a location the place it has a broad view outside the supposed house. If that is unavoidable, the lens might be masked to dam the view of undesired areas (confer with section I. Lens Masking). This guarantee is in lieu of all other express warranties, and the implied warranty of merchantability is restricted to one year from buy. This warranty does not cover the cost of set up, removal or reinstallation, or harm resulting from misuse, abuse, or injury from improper wiring or set up. This guarantee doesn't cover incidental or consequential damages. LUTRON’S Liability ON ANY Declare FOR DAMAGES ARISING OUT OF OR IN CON­NEC­TION WITH THE MANUFACTURE, SALE, Set up, Delivery, OR USE OF THE UNIT SHALL Never EXCEED THE PUR­CHASE Value OF THE UNIT. This guarantee gives you specific legal rights, and you could produce other rights which range from state to state. Some states don't permit the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied guarantee could last, so the above limitations may not apply to you. Patents pending. Lutron, Maestro Wireless, and the Sunburst logo are registered trademarks and Radio Powr Savr is a trademark of Lutron Electronics Co., Inc. ANSI is a registered trademark of the American National Requirements Institute. IEC is a trademark of the Worldwide Electrotechnical Commission. Made and printed within the U.S.A. 25/09/09 P/N 041-172 Rev. A 8 ft (2.4 m) 18 x 18 ft (5.5 x 5.5 m) thirteen ft (4.0 m) 9 ft (2.7 m) 20 x 20 ft (6.1 x 6.1 m) 14.5 ft (4.Four m) 10 ft (3.0 m) 22 x 22 ft (6.7 x 6.7 m) 16 ft (4.9 m) 12 ft (3.7 m) 26 x 26 ft (7.9 x 7.9 m) 19 ft (5.Eight m) Momentary Mounting Methods 1.1 1.2 Insert the ceiling tile mounting wire by way of the 2 smaller holes in the mounting bracket and exchange the mounting bracket. Mount Sensor to a ceiling tile by inserting the wire legs by the tile, ensuring the Sensor is flush to the tile. Word: Do not twist wire legs collectively. 1.2 After the Sensor has been quickly mounted, go away the Sensor in place on the tile and either take the tile down or remove an adjoining tile to realize entry to the legs of the mounting wire on the again of the tile. Low Activity: That is the most sensitive setting and can detect very slight motions. This is the really useful setting, as it will work properly for almost all purposes. It is ideal for areas where occupants will often be seated for lengthy durations of time. Twist the wire legs collectively tightly so the mounting bracket remains snug against the tile. This setting is barely less sensitive than the Low Exercise setting and can be utilized for spaces that expertise regular activity. That is the least delicate setting and can be utilized for spaces that can typically solely expertise large motions, corresponding to foot traffic. The Low Exercise setting is the default and will carry out finest for most functions. Not often, if the Sensor is placed close to external noise sources equivalent to heating vents, air conditioning vents, or gentle bulbs, it could turn the lights on without occupancy or keep the lights on too long after vacancy. If this happens, altering the sensitivity to Medium Activity or Excessive Exercise should resolve the problem. Exchange the tile. Permanent Strong Ceiling Mounting 2.1 2.2 2.Three Superior Set-Up Operation The superior set-up is accessed through the use of the buttons on the again of the Sensor. Drill two 3/16 in (4.6 mm) pilot holes for the provided screw anchors. Press the anchors into the holes and tap flush with a hammer. To display the current setting, press and launch the specified button. An LED will illuminate briefly, indicating the current setting. Place the flat aspect of the mounting bracket in opposition to the ceiling and install the two supplied screws utilizing a hand screwdriver. To adjust a setting, press and hold the specified button until the LED corresponding to the present setting begins flashing quickly, indicating the setting can now be adjusted. Every subsequent button press of lower than 2 seconds will increment the mode to the subsequent out there setting. Urgent any of the opposite buttons will have no impact. To save lots of the selected setting, press and hold the button till the LED turns on strong, indicating the saved setting. In the course of the adjustment process, if there is no such thing as a activity for 30 seconds, the LEDs will turn off and no settings will likely be saved. Notice: Don't over-tighten. 2.Four Attach the Sensor to the mounting bracket by inserting and twisting in a clockwise path till the Sensor locks into place. To take away the bracket from the ceiling, grasp the removing tab on the adhesive strip and pull the tab VERY SLOWLY straight across the ceiling, stretching the strip until the bracket releases from the ceiling. Discard the strip. By no means pull the strip at an angle, as it may break or damage the ceiling surface. Note: Do not pull at an angle. Lens Masking (Optionally available) Each time doable, the Sensor needs to be installed in a location the place it can not easily see into areas outdoors the meant space, equivalent to hallways or adjacent rooms. If this example cannot be prevented, parts of the lens may be masked with the offered labels to dam the Sensor’s view of the undesired areas. It is recommended to take away the Sensor from the mounting bracket before making use of Superior Set-Up (Elective) the masking labels. The Sensor features several advanced set-up modes. For the vast majority of installations, the default settings will provide one of the best efficiency and you won't have to make the most of the superior set-up. The Occupancy model of the Sensor has three adjustable advanced set-up modes: Timeout, Auto-On, and Sensitivity. The Vacancy-Solely version has solely two modes (Auto-On not accessible). The default settings are listed under. The Sensor may be screwed onto the mounting bracket in a number of completely different orientations. Make sure to note the Sensor’s orientation earlier than taking it down and exchange the Sensor in the same orientation to ensure the intended space will get blocked. Outer lens sections correspond to the detection areas furthest away from the Sensor, while internal sections correspond to regions nearer to the Sensor. Watch out when applying the labels to avoid creating gaps between adjacent masked sections. The Sensor could detect movement by means of inadvertent gaps. All the time (Occupancy version solely) Timeout 30 min 15 min 5 min Auto-On All the time Low gentle Disable Exercise Timeout 30 min 15 min 5 min Superior Set-Up Modes Auto-On All the time Low gentle Disable Activity Activity: Low Activity Lens sections proven in white are masked with labels Timeout The Sensor will turn the lights off if no movement happens during the timeout interval. There are three accessible timeout settings: 5, 15, and half-hour. Lens Mask Lens sections shown in grey have not been masked Auto-On The automatic-on performance of the Sensor might be adjusted to manage how the lights reply upon initial occupancy. There are three accessible settings: All the time, Low gentle, and Disable. At all times: The lights will always turn on. Testing Sensor Coverage With the Sensor mounted on the ceiling, press and launch the "Test: Sensor" button on the front of the system. The lens will glow briefly, indicating the check mode has been entered. Note: There is a warm-up period of roughly forty seconds after the batteries are installed before the check mode will be activated. If the button is pressed during this time, the lens will flash continuously until the warm-up interval is full, and then the take a look at mode shall be automatically entered. Affirm the coverage space by walking by way of the space and observing the lens. The lens will glow stable each time motion is detected. If the lens remains off throughout movement, the Sensor cannot detect movement at that location. Press and launch the "Test: Sensor" button once more to exit the take a look at mode. If the button is just not pressed, the test mode will routinely day trip quarter-hour after being enabled, or 5 minutes after the last detected movement if the room is vacated. If the Sensor has important hassle detecting motion through the check, it should be moved to a different location and retested. If the Sensor still has poor detection from the brand new location, refer to the Troubleshooting section. Short-term Drop Ceiling Mounting Use this process if the Sensor will likely be mounted on a ceiling tile. The ceiling tile mounting wire is offered for both momentary and everlasting mounting of the Sensor to drop ceilings composed of a number of tiles. It is designed to allow temporary mounting, testing, and repositioning (if obligatory) of the Sensor without damaging a ceiling tile. Once the Sensor’s last position has been chosen, the mounting wire could be twisted to lock the Sensor in place completely. If the Sensor coverage and wireless communication exams have been successfully accomplished, use the mounting bracket as a template to mark the screw hole places with a pencil. Note: Pull very slowly. Max. Room Dimensions Radius of Coverage for Full Protection at Flooring If you're uncertain about accurately positioning the Sensor, the following temporary mounting and testing procedures are really useful to verify correct efficiency before completely installing the Sensor. Sensor’s detection vary depends on the ceiling top, as shown in the desk below. Notice: Do not disassemble, crush, puncture, or incinerate the batteries. Don't dispose of batteries in normal family waste. Please recycle, take to a proper battery disposal facility, or contact your native waste disposal provider relating to native restrictions on the disposal or recycling of batteries. O NOT mount the Sensor inside four ft (1.2 m) of HVAC vents or gentle bulbs put in beneath the ceiling line. Hotter rooms may cut back the Sensor’s skill to detect occupants. Use only excessive-high quality lithium batteries, size CR123, three V (ANSI-5018LC, IEC-CR17345). Do not use rechargeable batteries. Utilizing improperly rated batteries could damage the Sensor. For questions regarding the set up or operation of this product, name the Lutron Technical Assist Heart. Please provide exact model quantity when calling. U.S.A. and Canada (24 hrs / 7 days) Setting the Occupancy Mild Stage (occupancy model, dimming units solely) the Sensor to the mounting bracket by inserting and twisting in a clockwise 2.5 Attach course till the Sensor locks into place. Sensor coverage and wireless communication tests as described in 2.6 Carry out sections E. Testing Sensor Coverage and F. Testing Wireless Communication. The Sensor should be put in in a location the place it has a superb view of all elements of the room. The Sensor requires line of sight to function properly. If you can not see the Sensor, it can't see you. The Sensor can not see by way of glass objects akin to patio or shower doorways. The range and performance of the RF system is very dependent on a variety of complex elements corresponding to: · Distance between system parts · Geometry of the building construction · Construction of walls separating system components · Electrical gear positioned close to system elements Technical Help 2.2 Determine a location on the ceiling the place the Sensor may have a very good view of the room. 2.Three Take away the black "wall side" liner from the adhesive strip. The Sensor is designed for ceiling use only. Don't set up on ceilings larger than 12 ft (3.7 m) or non-ceiling surfaces. Doing so might significantly inhibit the Sensor’s performance. 4. Don't paint Sensor. · · · · The "Lights On" and "Lights Off" buttons ought to now change the lights in the room on and off, respectively, when pressed. Repeat the above process to arrange the Sensor with any further devices. The Sensor is meant for indoor use only. Operate between 32 °F and 104 °F (zero °C and forty °C). 1.1 a number of seconds. Sensor that has been set up. After approximately 6 seconds, the lens will flash rapidly a number of occasions, indicating the light level has been saved. All Sensors arrange with the Dimmer will now use the saved occupancy mild degree. 2. Clean Sensor with a tender damp cloth only. Don't use any chemical cleaners. Notice: This equipment has been tested and found to comply with the limits for a class B digital machine, pursuant to half 15 of the FCC guidelines. These limits are designed to offer reasonable protection in opposition to dangerous interference in a residential installation. This gear generates, uses and may radiate radio frequency power and, if not installed and utilized in accordance with the directions, might cause harmful interference to radio and tv reception, which might be decided by turning the tools off and on. The person is encouraged to attempt to correct the interference by a number of of the next measures: Reorient or relocate the receiving antenna. Increase the separation between the tools and receiver. Join the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the vendor or an experienced radio/Tv technician for help. Caution: Adjustments or modifications not expressly authorised by Lutron Electronics Co. may void the user’s authority to function this equipment. This system complies with Part 15 of the FCC rules. This machine must accept any interference acquired, together with interference that will trigger undesired operation. Switch 2.1 Set the Dimmer to the desired light level for coming into the room. 2.2 Save holding the "Lights On" button on the entrance of a Be aware: For both Sensor version, the lights will also be manually turned off at any time by utilizing the dimming or switching system directly. Necessary Notes or Add the Sensor to the Dimmer or Change by pressing and holding the "Lights Off" button on the front of the Sensor for roughly 6 seconds till the lens flashes briefly. The lights in the room may even flash three instances, indicating the Sensor has been successfully added. The Dimmer or Swap will exit set-up mode automatically. The sensitivity of the Sensor may be adjusted based on the anticipated level of exercise throughout the room. There are three out there exercise settings: Low Activity, Medium Exercise, and High Activity. Everlasting Drop Ceiling Mounting Notice: Go away the removal tab uncovered previous the edge of the bracket so it may be accessed for elimination later. 6 seconds till all LEDs on the system begin flashing. Launch the faucet button. Sensor is detecting motion in areas that are not fascinating, reminiscent of hallways or adjoining rooms, discuss with section I. Lens Masking. If Sensor detection is passable during this check, perform the wireless communication take a look at as described in part F. Testing Wireless Communication. Testing Wireless Communication This test should be carried out to confirm that the Sensor has been accurately set up with the corresponding dimming or switching device and that there's correct wireless communication from the chosen Sensor location. If the lights in the room are usually not on, flip them ON manually at the dimming or switching system. Press and release the "Lights Off" button on the front of the Sensor. The lights ought to flip OFF. Press and launch the "Lights On" button on the front of the Sensor. The lights should activate. If the lights do not respond appropriately, discuss with the Troubleshooting section. Low gentle: The lights will solely turn on robotically upon entry if there just isn't already ample ambient mild within the room. Hallway falls within Sensor’s coverage space. Disable: This setting converts the Sensor to vacancy mode. The lights is not going to routinely activate however will nonetheless routinely turn off after vacancy. The lights should be manually turned on through the use of the associated dimming or switching gadget. Notice: The 15-second vacancy grace period is energetic on this mode. Consult with the Sensor Operation part at the start of this doc for extra particulars. Troubleshooting Symptom Doable Causes Resolution Lights don't activate when area is occupied. Sensor just isn't correctly added to dimming / switching gadget(s). Sensor’s Auto-On setting is set to "Low light" or "Disable". The lights were not too long ago turned off manually and the timeout has not but expired. Sensor doesn't have full view of room. Sensor is exterior wireless vary of dimming/switching device. Refer to section B. Set-Up. Seek advice from section H. Advanced Set-Up. Dimming/switching gadget has been improperly wired. Mild bulb(s) burned out. Breaker is off or tripped. Sensor’s timeout is simply too brief for this software. Sensor doesn't have full view of room. Lens mask is improperly applied. Sensor’s sensitivity is too low. Sensor’s timeout has not yet expired. An external noise source corresponding to an HVAC vent is interfering. Consult with section A. Pre-Installation. Habits of lights doesn't match Sensor settings. Sensor coverage extends beyond room perimeter. The supposed setting was not saved. Multiple Sensors are added to a dimming/switching system and their settings don't match. Discuss with part A. Pre-Set up. Consult with part C. Sensor Placement or I. Lens Masking. Confer with section H. Advanced Set-Up. Check with part H. Advanced Set-Up. Sensor lens doesn't glow in response to motion during Sensor coverage testing. Sensor can not see motion as a consequence of obstruction. Room is too large or oddly shaped. Transfer Sensor to another location. Discuss with part C. Sensor Placement. A number of Sensors may be necessary for full room protection. Try moving Sensor to a new location or lowering sensitivity. Seek advice from part C. Sensor Placement or H. Advanced Set-Up. Lights turn OFF while space is occupied. Lights stay ON after house is vacated. Lens does not cease glowing during Sensor protection testing even when there isn't any motion. Lights do not reply accurately during wireless communication testing. Sensor lens flashes and lights do not activate when space is occupied. Battery has been installed incorrectly. An exterior noise supply equivalent to an HVAC vent is interfering. Consult with part C. Sensor Placement. Confer with part C. Sensor Placement or F. Testing Wireless Communication. Confer with part H. Advanced Set-Up. Refer to part C. Sensor Placement. Consult with part I. Lens Masking. Consult with section H. Superior Set-Up. Confer with part H. Superior Set-Up. Attempt moving Sensor to a new location or decreasing sensitivity. Confer with part C. Sensor Placement or H. Advanced Set-Up. Sensor is just not correctly added to dimming / switching gadget. Sensor is exterior wireless range of dimming/switching machine. Check with section B. Set-Up. Move Sensor closer to dimming/switching system and retry test. Check with section F. Testing Wireless Communication. Battery has been installed incorrectly. Dimming/switching machine has been improperly wired. Gentle bulb(s) burned out. Breaker is off or tripped. Battery is low. Discuss with part A. Pre-Installation. Take away sensor from check mode. Discuss with part E. Testing Sensor Coverage.


www.question2answer.org